In a perfect world, current that is sent along a conductive wire is supposed to reach the intended destination in full. However, this does not happen in the real world because some of the current is usually lost along the way. There are different reasons why the current gets lost along the way. In an attempt to prevent the loss of current, resistant sheathing is used to insulate conductive wires. Here are facts regarding Insulation tester.
Sometimes the current is lost if the insulating sheath is made from imperfect materials. Machinery and electric circuits are greatly affected when there is leakage of current due to imperfect cladding. Such a case can be controlled by frequently testing the insulating material to determine its perfectness. Testing the material frequently can help to catch problems in advance before injuries or device failure happens because of loss of current.
A cladding tester is usually used to carry out the testing. The tester tests the resistance of the insulating material to the flow of current thus, determining its integrity. There is very little loss of current for insulating materials of high quality. On the other hand, insulating materials of poor quality will allow large amounts of current to escape.
Testers measure various kinds of current when they are used to measure the quality of cladding a material is made of. The three main kinds of currents measured are capacitive, absorption, and leakage currents. Capacitive current refers to the initial burst of current that happens when voltage gets first applied to conductors.
Capacitive current is the same as the first burst of water that flows out of a hose when the tap is first opened. The flow of water is usually very high initially, but it rapidly drops as the hose becomes fully filled with water. In this case, it is the conductor becoming fully charged that leads to the drop in the current flow.
Absorption current is similar to capacitive current in that it starts out high but then drops. The only difference between these two kinds of currents is that absorption current drops at a much lower rate compared to capacitive current. The gradual drop in absorption current is due to the storage of potential energy in the cladding. Absorption current makes an important part of the time resistance method of cladding testing.
Leakage current is also referred to as conduction current. This is a small, steady current that is present both over and through the cladding. If the leakage current increases over time, it implies that the cladding is deteriorating over time too. Insulation test meter usually indicates these increase in leakage current as decrease in resistance.
Currently, different types of cladding testers are available in the market. Different manufacturers from different countries produce these devices. The manufacturer of the equipment largely influences its quality. Different models of cladding testers are used to perform different functions. For instance, some testers are designed to perform testing in residential settings while other testers are meant to be used for testing equipment in industries.
Sometimes the current is lost if the insulating sheath is made from imperfect materials. Machinery and electric circuits are greatly affected when there is leakage of current due to imperfect cladding. Such a case can be controlled by frequently testing the insulating material to determine its perfectness. Testing the material frequently can help to catch problems in advance before injuries or device failure happens because of loss of current.
A cladding tester is usually used to carry out the testing. The tester tests the resistance of the insulating material to the flow of current thus, determining its integrity. There is very little loss of current for insulating materials of high quality. On the other hand, insulating materials of poor quality will allow large amounts of current to escape.
Testers measure various kinds of current when they are used to measure the quality of cladding a material is made of. The three main kinds of currents measured are capacitive, absorption, and leakage currents. Capacitive current refers to the initial burst of current that happens when voltage gets first applied to conductors.
Capacitive current is the same as the first burst of water that flows out of a hose when the tap is first opened. The flow of water is usually very high initially, but it rapidly drops as the hose becomes fully filled with water. In this case, it is the conductor becoming fully charged that leads to the drop in the current flow.
Absorption current is similar to capacitive current in that it starts out high but then drops. The only difference between these two kinds of currents is that absorption current drops at a much lower rate compared to capacitive current. The gradual drop in absorption current is due to the storage of potential energy in the cladding. Absorption current makes an important part of the time resistance method of cladding testing.
Leakage current is also referred to as conduction current. This is a small, steady current that is present both over and through the cladding. If the leakage current increases over time, it implies that the cladding is deteriorating over time too. Insulation test meter usually indicates these increase in leakage current as decrease in resistance.
Currently, different types of cladding testers are available in the market. Different manufacturers from different countries produce these devices. The manufacturer of the equipment largely influences its quality. Different models of cladding testers are used to perform different functions. For instance, some testers are designed to perform testing in residential settings while other testers are meant to be used for testing equipment in industries.
About the Author:
Find details about the benefits you get when you use an insulation tester. If you have any questions, see the main page at http://www.rossengineeringcorp.com.
No comments:
Post a Comment