The first thing you must know when you build an electrical device with your own circuits are theories on basic electronics. Find out the various components used for them and the ways of properly connecting them with each other. Study also how to create and read a schematic diagram which graphically represents an electrical circuit with symbols and images.
Doing so is important when you like to make a particular device but still confused on some parts of this process. This may be something a bit advance for you like the voltage divider which the output produced is a portion only of its input. Before tackling that, learn first or review the basic theories in electronics to better understand the advance stuffs.
Start by identifying the two kinds of electricity that are direct current and alternating current which are also known as DC and AC respectively. In AC, the direction where the electrical signal flows is alternating or reversing constantly with Hertz used to measure the reversal rate. In DC though, the movement is one directional from power source, commonly batteries, into the ground.
Circuit is closed if the path allows the electric current to pass through from a power source into the ground which usually indicates the device is turned on. An open one on the other hand breaks the path and would prevent movement such as when turning off machines. A switch is used in doing this so removing the source is not necessary when alternating between them.
When current pass through components, they create resistance to ground from positive voltage and if these are directly connected, this would cause the circuit to be shorted. This direct connection would result in fire, breaking, overheating or explosion which you must avoid. Putting switch would not provide additional resistance so other parts must be added.
Wiring things together can be done in two ways which are called series and parallel with the former indicating that all components are wired after the other. While the latter indicates that the parts are wired next to each other and which makes electricity pass them simultaneously. Both ways could be used in building your own circuits.
Resistors are used to add resistance into circuits and reducing their current flow with ohms used in measuring its different values. They have also wattage ratings and the colored bands surrounding their body indicates their resistance value. You can learn these colored bands or search for graphs which helps calculate their values instead.
Components which stores electricity and discharges them when they drop are called capacitors and is measured with Farads commonly shown in units of nanofarad, picofarad and microfarad. The types of capacitors commonly used are electrolytic and ceramic disc. The latter being non polarized while the former is polarized requiring one leg to connect properly with either the ground or power.
Diodes are components that are polarized allowing one direction of passage for currents and causes a voltage drop as well. The side called cathode connects to the power and the opposite side is called anode. These are samples only of a few basic theories so research more about them.
Doing so is important when you like to make a particular device but still confused on some parts of this process. This may be something a bit advance for you like the voltage divider which the output produced is a portion only of its input. Before tackling that, learn first or review the basic theories in electronics to better understand the advance stuffs.
Start by identifying the two kinds of electricity that are direct current and alternating current which are also known as DC and AC respectively. In AC, the direction where the electrical signal flows is alternating or reversing constantly with Hertz used to measure the reversal rate. In DC though, the movement is one directional from power source, commonly batteries, into the ground.
Circuit is closed if the path allows the electric current to pass through from a power source into the ground which usually indicates the device is turned on. An open one on the other hand breaks the path and would prevent movement such as when turning off machines. A switch is used in doing this so removing the source is not necessary when alternating between them.
When current pass through components, they create resistance to ground from positive voltage and if these are directly connected, this would cause the circuit to be shorted. This direct connection would result in fire, breaking, overheating or explosion which you must avoid. Putting switch would not provide additional resistance so other parts must be added.
Wiring things together can be done in two ways which are called series and parallel with the former indicating that all components are wired after the other. While the latter indicates that the parts are wired next to each other and which makes electricity pass them simultaneously. Both ways could be used in building your own circuits.
Resistors are used to add resistance into circuits and reducing their current flow with ohms used in measuring its different values. They have also wattage ratings and the colored bands surrounding their body indicates their resistance value. You can learn these colored bands or search for graphs which helps calculate their values instead.
Components which stores electricity and discharges them when they drop are called capacitors and is measured with Farads commonly shown in units of nanofarad, picofarad and microfarad. The types of capacitors commonly used are electrolytic and ceramic disc. The latter being non polarized while the former is polarized requiring one leg to connect properly with either the ground or power.
Diodes are components that are polarized allowing one direction of passage for currents and causes a voltage drop as well. The side called cathode connects to the power and the opposite side is called anode. These are samples only of a few basic theories so research more about them.
About the Author:
You can get great tips for picking a voltage divider supplier and more information about a reliable supplier at http://www.rossengineeringcorp.com/products/measurement/hv-voltage-dividers/hv-voltage-dividers-detailed-info.html now.
No comments:
Post a Comment